Toggle Nav
My Cart
Search
Advanced Search
  1. HOME
  2. E-Store
  3. Cart
  4. Login
  5. Registration
  6. Contact Us
  7. NCE Repair/Warranty

ADAPTERS/ WIRE/SWITCHPILOTS/LEDs

26 Items

per page
Set Descending Direction
  4. Lighting Upgrade Lighting Upgrade

    DCC Solutions

    Special lighting upgrades for a range of locomotives equipped with a 21 pin locomotive decoder adds the two physical functions to the Loksound Select or Lokpilot decoders allowing separate operation of the white and red markers. This allows the locomotive to display its markers in a prototypical manner. The DCC Solutions DCC lighting upgrades come complete with full-colour instructions written specifically for each locomotive. Note that these upgrades will work with other 21 pin decoders. Size 22 mm x 2.5 mm x 2.5 mm

     

    Click ADD to View Options & prices.
    A$25.00
  15. PowerPack PowerPack

    Power Pack-Energy Storage for Loksound L V4 & Select. It has an integrated charging current which is controlled by the decoder. Therefore it can remain within the loco while it gets programmed. The load current is however, limited to avoid an excessive load on your booster, for this case there would be, several models in operation.
    The buffer time can be restricted by writing a CV on the decoder side to make red signals lead to an exact signal stop.
    Power Pack Maxi -  28 x 16 x 13 mm 
    A 3-pin cable connection between the decoder and the Power Pack is essential.

     

    V4
    A$110.00
  16. LED Lighting Strips Tail light

    ESU

    Interior LED lighting system for passenger cabins, prototypical and steady interior lighting. Available in three different versions to match the desired location and is available in multiple options including:
    - Colour options (warm white; yellow; and yellow/white switchable).
    - Red taillight on all options.
    - Adjustable brightness of the light via a small potentiometer.
    - Can be cut to suit your needs without the need for extra wiring.
    - Supports the ESU Lokpilot FX decoder to allow you to control the lighting from your DCC throttle.

     

    Click Add to view Options & prices.
    A$0.00
  17. ESU-Smoke Unit ESU-Smoke Unit

    ESU

    LokSound XL decoder can handle many commercially available smoke generators, we recommend ESU smoke generators. 
    Integral electronics control both the fan and the heating system of the smoke generator with a temperature sensor, the amount of smoke is independent of the track voltage and will burn if the tank is empty.
    The amount of smoke and revs of the fan can be determined by the LokSound XL V4.0 decoder allowing both steam smoke plumes as well as diesel exhaust plumes. Steam exhaust plumes can be synchronized by external triggers or can be determined by the LokSound XL decoder.  It also accepts commands via the SUSI interface.
    Sizes: 54679 dimensions - 50 x 28 x 30 mm, 
         
    54679
    A$160.00
  19. Extension Board Extension Board

    ESU

    This expansion board can easily expand your LokPilot V4.0 or LokSound V4.0 decoder (with 21MTC interface!): Benefit from 4 additional function outputs (AUX5 through AUX8) for lighting effects, coupler etc or connect 2 RC-servos! The highlight of the expansion board is the control electronics for synchronised smoke units, just install an ESU smoke unit to generate synchronised steam chuffs or Diesel smoke.
    The board measures 15.5mmx 30mmx 5.5mm (0.61 x 1.18 x 0.22 inch)
    The module can be directly plugged into a 21MTC interface of a loco (if enough height available) .
    Extension Board 21 pin
    A$86.00

26 Items

per page
Set Descending Direction
Products
open all | close all
 
 
© 2019 MRRC . All Rights Reserved.