DCC CONTROL

NCE decoders for locomotives with N scale Kato drive mechanisms using the side tab motor clips.

This decoder has four function outputs.

Size: 68 x 9.0 x 3.0 mm.

Lais KungFu decoder

9 wires plus Blue +Black wire

• Scale: HO & N scale,  Function: 4*100mA, Standard: NMRA DCC, Not Support: ABC, Railcom, Motorola, Total support of all NMRA/NEM specs. Direct easy connection to Stay-Alive device. 4 digit addressing and 14, 28 or 128-speed steps. Back EMF with step-variable or FN button control. 2Amp peak, 1A continuous, Functions 100mA

TDS HB 1.1"

28 mm (1.1") dia
30.7 mm (1.2") with enclosure
5.1 mm (0.2") H
8 mm (0.32") 1/2 enclosure
13.1 mm (0.52") full enclosure
8 Ohm, 2W.

TCS T6X-Series

HO scale decoder with 9 pin JST socket and loom.

Provides 1.3 amp continuous and 2 amp peak draw, auto-adjusting BEMF with two lighting functions (headlight and reverse light).

T6X - 6 function

The LED models connect directly to LED installaions using the TCS LED's

Size: 96”x.66”x.21” or 24.3 x 16.7 x 5.3mm

NCE - TOGGLE SWITCH DPDT  

NCE

Momentary SPST-Red, Green, Black - 8pk

DCC Bus Wire, Black

14 AWG, 25, 50, and 100 Feet.

TCS

10-foot lengths of the 32 gauge wire .022" diameter.

TCS

20 foot lengths of 32 gauge wire.

TCS

10-foot lengths of 30 gauge wire.

TCS

20 foot lengths of 30 gauge wire.

NCE

Euro 3-5   3 Circuit

Terminal Block 5 pk

NCE

Euro 2-5   2 Circuit

Euro StyleTerminal Block 5 pk

SPECIAL ORDER ONLY

NCE CS-02 Command Station

The CS 02 is the NCE Power Pro Command Station and is the most user friendly DCC system on the market. Plug in EPROMs allow you to update the system and no need to return the unit to the factory.

This is and ideal path for those wishing to move from another DCC system and seeking the NCE advantage. When migrating please contact us as most boosters are compatible with the NCE CS 02 Command station.

CS 02 Specifications:
* Cabs: 60 maximum
* Number of simultaneous trains: 250
* Number of consists: 127 
* Range of locomotive addresses: 0-9999
* Range of consist addresses: 1-127
* Range of accessory addresses: 1-2044
* RS232 computer interface included

NCE Pro Cab

The Pro Cab throttle provides the most user-friendly access to all system features. Uncomplicated menus on the easy to read, the backlit LCD display will guide you through the most advanced operations with a minimum of fuss.

The Pro Cab-R throttle has the same specification as the Pro Cab except that a radio board and battery holder has been added for operation as a radio throttle while retaining the plug capability of the Pro Cab.

FUNCTION CONTROL FOR THE LOCOMOTIVE LIGHTS F9 to F12

NUMBER KEYS

The keys 0 through 9.

When operating a loco if a number key is pressed it toggles the corresponding function on the loco. Use to access FUNCTIONS 1 to 9.

To access the function F9 you simply press 9

 SHIFT BUTTON

When pressed and held while pressing another key on the cab the alternate value of that key can be used.

To access the function F10 you simply press SHIFT and PROG/ESC at the same time to activate FUNCTION 10.

To access the function F11 you simply press SHIFT and EXPN at the same time to activate FUNCTION 11.

To access the function F12 you simply press SHIFT and 28/128 at the same time to activate FUNCTION 12.

Repeat the procedure to turn the function off.

How to operate the DCC Solutions 28 functions on your locomotive.

 EXTENDED FUNCTION CONTROL F10 to F28

 OPTION BUTTON

The OPTIONS button marked * (see picture) can be reprogrammed for use to access FUNCTIONS 10 to 28. Follow these simple steps.

1. Turn on your system and unplug the cable from your cab (Throttle)

2. Press and hold down the SELECT LOCO while plugging the cable back into your cab. The cab will now enter the initial setup program. At any time you may press PROG/ESC to exit.

3. Press enter FOUR (4) or possible FIVE (5) times depending on your cabs firmware until your screen reads PROG OPTION KEY...KEY VALUE = 94.

4. Enter a new value of 122 and press ENTER

5. Press PROG/ESC to exit.

Once reprogrammed pressing OPTION once will display F10 – F19 and pressing it twice will display F20 – F28. Pressing a number key will toggle that number plus 10. Example: Press OPTION once then 5 will activate F15. Repeat the same procedure to turn F15 off.

NCE Cab06 and Cab06R

The Cab06e uses an encoder knob for speed control. The Cab06 can be set to YARD mode. Yard mode makes the speed knob act as a "centre off" speed control. Turn the knob to the right and the loco will increase speed in the forward direction. Turn it to the left and speed will decrease until it gets to zero then it will start to increase speed in the reverse direction the farther you turn it to the left. Selection and control of individual or entire routes through turnouts (via the MACRO key), and our unique OPTION button that can be programmed to act as any button you wish, even those found on a much larger cab.

• Additional features include a 4-digit LED display, 29 functions, accessories with 6 recalls, including PowerCab

• The Cab06eR has the same specification as the Cab06, except that a radio board and battery holder have been added for operation as a radio throttle while retaining the plug capability of the CAB06. 

• For those who do not wish to use an encoder, NCE offer the CAB06P and CAB06PR. All the great features of the CAB06e but with a potentiometer.

• The MRRC recommends the Cab06P for radio operation as it offers a physical stop to mark stop.

NCE

Control one twin coil switch machine. Has capacitive discharge for low current draw of track power. Provides connections for two "local control" pushbuttons. You can control switches from cabs and mini panels.

Made to fit the Intermountain FT-A with two functions

NCE

The Auxiliary Input Unit provides connection of block occupancy detectors, switch position relays, etc. for purposes of signaling and/or computer control of your layout.

Simply plugs in to the Cab Bus.

Note: To be used with the NCE PowerCab the adress must be set at four [4]

NCE

Detects DCC current being drawn in a block.

Connects to AIU-01 & Mini Panel for PC and automated control.

Works with most commercial signal systems.

Supports analogue output to 40 ma - requires a TX-01

NCE

RJ12 Coil cable for cabs

NCE

RJ12-7' Cable for connecting UTP/DIN panel

NCE

12 foot RJ12 Cable for connecting UTP/DIN panel

NCE

40'- RJ12 Cable for connecting UTP/DIN panel

NCE

Provides short circuit protection for one power district. Can be used with most DCC systems.

This is recommended for use with the Power Cab as a primary means of protection with the EB1 set to 1.5 amps for a distributed protection add a CP6.

NCE

CP6 Circuit Protector

Provides circuit protection for up to six sections of your railroad. Operates with any DCC system. Each globe allows 1 amp per section and sections can be connected together for more power per section.

NCE Quick Connect

Simply crimp to a NCE Feeder wire and push onto a NCE bus tap

No soldering required

Quick and easy

NCE Quick Connect

Simply crimp to a NCE Feeder wire and push onto a NCE bus tap

No soldering required

Quick and easy

NCE Bus Tap

Simply clip around the NCE bus wire & connect using a NCE connector

Blue 14 - 16 AWG

No soldering required

NCE

6 foot CAT5 cable for connecting UTP CAT panel

NCE

16 foot CAT5 cable for connecting UTP CAT panel

NCE Bus Tap

Simply clip around the NCE bus wire & connect using a NCE connector

Blue 14 - 16 AWG

No soldering required

NCE Bus Tap

Simply clip around the NCE bus wire & connect using a NCE connector

Blue 14 - 16 AWG

No soldering required

NCE Bus Tap

Simply clip around the NCE bus wire & connect using a NCE connector

Yellow 10 - 12 AWG

No soldering required

TCS

34 Gauge .006" .16mm Diameter Magnet Wire 20' 6.1m Roll

Green

TCS

34 Gauge .006" .16mm Diameter Magnet Wire 20' 6.1m Roll

Red

TCS 21-HWM- 5pk 21-Pin NEM Male Hardwire

TCS 4-Point Junction Board 25pk

Each: .33 x .28 x .03" or 8.38 x 7.11 x .76mm

TCS DCC Decoder Socket 

9-Pin JST Socket (Female) 5pk

Ultra-Miniature Furnace/Forge/Sawdust Burner Simulator Circuit Board

For Use w/Sound DCC Decoders & RC Applications - Input: 3.3-18V DC

Ultra-Miniature Simulator Circuit Board - DCC & Stationary Use; Input 6-18V DC

Steam Locomotive Class Light

Lighting Effects Circuit for Any Scale

Smaller than any decoder at just .31" x .31" x .118" and utilizing the industry's smallest microcontroller and associated voltage control circuitry, the total module consumes less than 500 µa (<1/2 ma). Typical peak operating current for these modules with LED(s) attached and running through full brightness curves range from 18-38 ma. This makes them ideally suited for operation when powered directly by a function output of any of today's HO, N or Z-scale DCC decoders. Designed specifically to provide truly realistic lighting effects for 20ma LEDs, these modules include input protection against reverse polarity. Input voltage range 6-18 VDC. On-board current limiting resistor. Extra input wires included. LEDs sold separately.

DC Power Source

Single Pack

Ngineering

HO - 6"Aluminium Escutcheon - 8pk

Ngineering

HO - 18"Aluminium Lampshade

These aluminum lampshades and escutcheons have a very thin (.005") cross-section for prototypical appearance. The concave shape easily accepts many lighting products. Mounting holes are easily added.

Ngineering

O scale - 12"Aluminium Lampshade - 8pk

HO scale - 24"

2 each

MicroSuper-white LED .030 x .060" 

Extremely small size of just .030 x .060 and very bright, pure white light output. Device Voltage: 3.3V DC, Current: 20 ma, Average Life: 50-80,000 hours.

Ngineering

100uf Tantalum Capacitor - 6pk 

These tiny 16V DC capacitors can be "ganged" in parallel. Perfect for rolling stock lighting flicker control.

Ngineering

1/8-Watt SMD Resistor - 20pk

1500-Ohm

These precision resistors fit in the smallest spaces due to their flat shape and miniature size. Solder pads on each end are pre-tinned

Ngineering

1/8-Watt SMD Resistor - 20pk

1000-Ohm

These precision resistors fit in the smallest spaces due to their flat shape and miniature size. Solder pads on each end are pre-tinned

Ngineering

Micro Super-White LEDs - 10pk

Extremely small size of just .030 x .060 and very bright, pure white light output. Device Voltage: 3.3V DC, Current: 20 ma, Average Life: 50-80,000 hours.