DCC CONTROL

ESU

The 21 MTC adapter board 2 is also suitable for digitizing a loco without interface, or wish to use more than four function outputs on your decoder. 

On the output side, the adapter offers soldered cables (appr. 20cm length) . There are amplifiers (appr. 250mA each) for function AUX3 and AUX4 so that ESU decoders can have up to 6 available physical functions.

Servo Centering Tool

Keep your servos centered while you mount them under the layout.  The tool consists of a battery box connected to a small circuit board that continuously puts out a centering signal for the servo (1.5 ms pulse). Keeping your servos porperly centered while mounting is the key to making the servos work best. The battery box has an on/off switch to save your batteries when not in use. Everyone using servos for turnouts needs one of these. Requires 3 AA batteries.

High quality minature speaker including baffle and harness.

8 ohms impediance.

Supplied with enclosure fitted.

DCC Solutions

Special lighting upgrades for a range of locomotives equipped with a 21 pin locomotive decoder adds the two physical functions to the Loksound Select or Lokpilot decoders allowing separate operation of the white and red markers. This allows the locomotive to display its markers in a prototypical manner. The DCC Solutions DCC lighting upgrades come complete with full-colour instructions written specifically for each locomotive. Note that these upgrades will work with other 21 pin decoders. Size 22 mm x 2.5 mm x 2.5 mm

Save your layout and models from the danger of spilling liquid from drinks while you're working or operating with our new adjustable folding drink and tool holder.

Features

• Adjustable width will hold cans as well as larger drink cups

• Folds flat when not in use to save space

• Includes four black wood screws

• Black textured finish

• Made from durable ABS plastic

• LAIS #860064

  Capacitor Discharge Unit – CDU – 4x 4700uF

  Provides a high current pulse to “snap” points across positively from the capacitors Limits subsequent points current to prevent coil burn out Prevents voltage drop to other parts of the installation during points action. Operates on AC or DC supplies. Uses a high quality industrial double-sided PCB  

LAIS - Stayin Alive Kits 

Used to supply power to decoders during times of power interruption due to dirty track or problematic track work.

Will power HO Scale locomotive for approximately 6 to 20 seconds (depending on the locomotive and the efficiency of the motor). Includes a blue and a black wire with which to attach it to a decoder. The blue wire is the positive/DC+, the black wire is the GND. You can use it with sound decoders and mobile decoders.

Custom installation kit for 23 mm ESU speaker including lead and plug

Speaker installs into roof of locomotive - crew height must be adjusted slightly to clear speaker

Speaker included - soldering required

Instruction page - CLICK HERE

Lais

Arc Welding Simulator, uses white & blue LEDs to give a bright pulsating light similar to that of an electric arc welder.

NCE- Circuit Blocks - 2pk

Euro Style 8-2 Terminal Block 14-24 AWG.

NCE - Circuit Blocks

Euro Style 4-4 Terminal Blocks - 4pk

NCE

Euro 6-3 -  6 Circuit

Terminal Block 3 pk

NCE - Spare parts

Thumbwheel / Encoder assembly for Pro Cab and Power Cab.

Note: Soldering is required.

ESU Speaker

16mm x 35mm 8 Ohms Speaker with Enclosure

Lais

Pre-Soldered Micro Litz Wired Leads SMD Led Warm White - 10pk

Forward Voltage 2.8V-3.4V

AC or DC Compatible

Forward Current 15ma-20ma

LAIS #860065

Automatic Brake Controller, will generate asymmetric DCC to activate the braking feature on suitably equipped DCC decoders.

NCE

DCC Black Bus Wire, 14 AWG stranded wire.

NCE Membrane Keypad 

For Engineer Cabs 04/5/6

NCE

DCC Bus Wire Red, 14AWG,

BRAWA

Distribution Plate - 5 Fold - #2591

Consignment Very Good Condition

ESU 

Adapter Board 21MTC to 9-pin JST. 

STX

Quick-Disconnect harness assembly for separating locomotive from tender offering 9 pins and a pcb plug with mounting hole

This decoder can be used to drive LEDs in a variety of lighting applications.  It can be used to drive 3-LED signal heads as it is set up for JMRI (type Double Output).  Can also be used to light a building or a car.  with the flicker function it can imitate a flickering light bulb, a welding arc or a campfire.  Although the outputs are marked R Y G for ease of wiring to a signal head, any color LED can be used.  In addition there is a mode for driving a 2-lead bi-color LED.

The decoder uses 2 consecutive DCC addresses - one controls the R output and the other controls the G output.  If both are on then the Y output is lit.

Reduces or eliminates voltage spikes on long runs of DCC bus wire,this is especially important on any DCC track bus wire 40 feet [12 meters] or longer. 

Protects decoders from damaging inductive voltage spikes while help preveting temporary loss of control or runaway problems by preserving DCC waveform accuracy.

WHAT ARE THE SIGNS YOU MAY NEED A RC FILTER ON THE TRACK BUS?

1) Loss of train control

2) Runaway engines (Take off) :

3) Loss of decoder programming. 

4) Decoders blowing up.

Consider installing a snubber at the end of each cab bus

• LAIS FX only: 860011

• Warranty: 90 days
• Current Rating:1 Amp
• 7 Wires does not have wire for motor 
• Four [4] functions
• Dimensions:18mm*12mm*3mm

DCC Bus Wire, Black

14 AWG, 25, 50, and 100 Feet.

NCE

Euro 3-5   3 Circuit

Terminal Block 5 pk

NCE

RJ12 Coil cable for cabs

NCE Quick Connect

Simply crimp to a NCE Feeder wire and push onto a NCE bus tap

No soldering required

Quick and easy

NCE

16 foot CAT5 cable for connecting UTP CAT panel

NCE Bus Tap

Simply clip around the NCE bus wire & connect using a NCE connector

Blue 14 - 16 AWG

No soldering required

NCE Bus Tap

Simply clip around the NCE bus wire & connect using a NCE connector

Yellow 10 - 12 AWG

No soldering required

TCS 4-Point Junction Board 25pk

Each: .33 x .28 x .03" or 8.38 x 7.11 x .76mm

Ultra-Miniature Simulator Circuit Board - DCC & Stationary Use; Input 6-18V DC

Steam Locomotive Class Light

Lighting Effects Circuit for Any Scale

Smaller than any decoder at just .31" x .31" x .118" and utilizing the industry's smallest microcontroller and associated voltage control circuitry, the total module consumes less than 500 µa (<1/2 ma). Typical peak operating current for these modules with LED(s) attached and running through full brightness curves range from 18-38 ma. This makes them ideally suited for operation when powered directly by a function output of any of today's HO, N or Z-scale DCC decoders. Designed specifically to provide truly realistic lighting effects for 20ma LEDs, these modules include input protection against reverse polarity. Input voltage range 6-18 VDC. On-board current limiting resistor. Extra input wires included. LEDs sold separately.

DCC Bus Wire, Red

14 AWG, 25, 50 and 100 Feet.

Remote Aligner for Octopus III

Used with the Octopus III to align of servos (cannot be used with the Octopus II). 

Just one of these needed for all of your Octopus IIIs. 

Suppied with a 7' cable for ease of installation.

Board is 2.7" x 1.7" in size

NCE

The operator side is fitted with RJ-12 jacks for throttles while offering CAT5 cable connections for improved noise rejection on larger layouts using standard computer CAT 5 cables. This board also provides a convenient point to add additional 12 Volt cab bus power when bus lengths exceed 20 meter [60 feet]. Shown with the included fascia plate.

Power Drop Wire

Simply crimp a NCE Quick Connect & push onto a NCE bus tap

No soldering required

Power Drop Wire

Simply crimp a NCE Quick Connect & push onto a NCE bus tap

No soldering required