DCC CONTROL

ESU Wire

Super thin, extremely flexible wire,(AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colours. They come in 10 m (30 feet).

ESU

Interior LED lighting system for passenger cabins, prototypical and steady interior lighting. Available in three different versions to match the desired location and is available in multiple options including:

- Colour options (warm white; yellow; and yellow/white switchable).

- Red taillight on all options.

- Adjustable brightness of the light via a small potentiometer.

- Can be cut to suit your needs without the need for extra wiring.

- Supports the ESU Lokpilot FX decoder to allow you to control the lighting from your DCC throttle.

Micro Servo Bracket Kit (servo not included)

3D Printed Bracket for Mounting a Micro Servo under the Layout for turnout control. 

Switch Wright Servo bracket, provides a Centre-Over Spring to Securely Hold Points.

LAIS

NEM652 8pin HO DCC Base Board for Bachmann & Athearn Trains.

Add a nice touch to your layout with our custom-made pockets to hold your Atlas, CVP EasyDCC, Digitrax, Lenz, or NCE DCC throttles. These pockets are injection molded from durable ABS plastic. Simply fix using the supplied screws to your layout and you're ready for operations.

• Includes four black wood screws

• Black textured finish

• Made from durable ABS plastic

LAIS 

Next18 NEM662 Adapter Board 18pin to Wires.

ESU Adapter

18pin Next-18 socket to NEM 651 with 6pin plug. 

STX - Speakers

Various Sizes.

Lais

21p/21MTC Male to 21 wire Adapter, convert a decoder with wires to a 21MTC 21pin decoder.

NCE Quick Connect

Simply crimp to a NCE Feeder wire and push onto a NCE bus tap

No soldering required

Quick and easy

30-32 Gauge Wire

Red - Right hand rail

Black - Left hand rail

Gray/Orange - Motor

Blue - Positive common

White - Front Headlight

Yellow - Rear Headlight

Genaral assignments but can vary

Green/Viloet - F1 / F2

Brown - Speaker

Shrink Tube for Decoder Installations - 70mm lengths

ESU 

16mm x 26mm square 4 ohms speaker with enclosure.

LAIS 

DCC 8pin Nem652 Socket with Solder Tabs.

LAIS #860039

Compact Circuit Board For Railroad Crossing Signals LED Flash

Safety Blinkers For Bicycles

LAIS

DBX-9000 Wiring Kit for Tender

SOUNDTRAXX

IC Magnetic Wand for use with Soundcar equipped Freight cars.

Activates intelligent consisting.

ESU

2 x 13mm, 8 Ohms, Round speakers with enclosures.

ESU 

20mm x 40mm square 4 ohms speaker with enclosure.

STX

A quick and easy way to install cams for cam-synchronized exhaust. For use with all SoundTraxx Steam Digital Sound Decoders with a cam output

TDS050-E

0.50" Dia Speaker

TDS062-E

0.62" Dia Speaker (16mm)
17.9 mm (0.7") dia enclosure
3.5 mm (0.14")H 
7.4 mm (0.29") 1/2 enclosure
12.5 mm (0.49") full enclosure

TDS075-E

0.75" Dia Speaker (20mm)
22.2 mm (0.87") dia enclosure
3.4 mm (0.13")H
6.9 mm (0.27") 1/2 enclosure
12.1 mm (0.47") full enclosure

TDS100-E

1.00" Dia Speaker (26mm)
28.5 mm (1.12") dia enclosure
4.7 mm (0.185")H
8.1 mm (0.32") 1/2 enclosure
13.2 mm (0.52") full enclosure

TDS110-E

1.00" dia Speaker (26mm)
30.7 mm (1.2") dia enclsure
5.1 mm (0.2")H
8 mm (0.32") 1/2 enclosure
13.1 mm (0.52") full enclosure

TDS120-E

1.2" dia speaker (28mm)
30 mm (1.17") dia
31.9 mm (1.25") dia
5.7 mm (0.22")H 
12.5 mm (0.49") 1/2 enclosure
20.4 mm (0.8") full enclosure

MICRO OVAL-E

15 x 10 mm (0.59" x 0.39")
3.5 mm (0.14")H

MINI OVAL-E

Snap Fits a Mini-Oval Speaker:

25 x 14 mm (0.56" x 1.0") 

SMALL OVAL-E

35 x 16.2 mm (1.38" x 0.63") speaker
18.3 mm (0.72") W enclosure
36.9 mm (1.45") L enclosure
9.1 mm (0.36") H enclosure

MEDIUM OVAL-E

34.7 x 20 mm (1.37" x 0.79") speaker
21.8 mm (0.86")W enclosure
36.8 mm (1.45")L enclosure
9.7 mm (0.38")H enclosure

HB106R-E

27 dia x 16 mm (1.06" x 0.6") speaker
30.5 mm OD (1.2") dia enclosure
21.5 mm (0.85")H enclosure

HB110S-E

High Bass 1.10" Sq. x 0.0.44" speaker
35.0 x 35.0 mm (1.38" sq) enclosure
13.8 mm (0.55")H enclosure

HB122R-E

High Bass 1.22" Dia x 0.63" speaker
39.0 mm OD (1.54") dia enclosure
22.5 mm (0.89")H enclosure

TDS050

0.50" Dia Speaker (13mm), 8 Ohm

TDS062

0.62" Dia Speaker (16mm)
17.9 mm (0.7") with enclosure
3.5 mm (0.14") H 
7.4 mm (0.29") 1/2 enclosure
12.5 mm (0.49") full enclosure 
8 Ohm, 0.1 W

TDS100

1.00" Dia Speaker (26mm)
28.5 mm (1.12") with enclosure
4.7 mm (0.185") H
8.1 mm (0.32") 1/2 enclosure
13.2 mm (0.52") full enclosure 
8 Ohm, 0.4 W

TDS-1.20"AT

30 mm (1.17") dia
31.9 mm (1.25") with enclosure
5.7 mm (0.22") H 
12.5 mm (0.49") 1/2 enclosure
20.4 mm (0.8") full enclosure 
8 Ohm, 

TDS-Small Oval Speaker

35 x 16.2 mm (1.38" x 0.63")
18.3 mm (0.72") W with enclosure
36.9 mm (1.45") L with enclosure
8.1 mm (0.37") H
9.1 mm (0.36") H with enclosure 
8 Ohm, 1.0 W

TDS Round Speaker

1.10" Round-28mm dia

High Bass Speaker

HB 0.90" sq.dia 23mm

8 Ohm, 1-2 Watts 

Fascia Controller Bicolor for SwitchWright/Quad/QuadLN/Octopus II/Octopus III

This controller is identical to the above controller except that it has two Red/Green Bicolor LEDs instead of the 2 yellow LEDs.  Each LED alternates between red and green so both LEDs are lit whereas in the regular yellow LED controller one LED is on at a time.  The LED colors in photo are a bit washed out due to the limits of photography. Other than the LEDS it is identical to the single-color Fascia Controller.

TDS HB 1.1"

28 mm (1.1") dia
30.7 mm (1.2") with enclosure
5.1 mm (0.2") H
8 mm (0.32") 1/2 enclosure
13.1 mm (0.52") full enclosure
8 Ohm, 2W.

NCE - TOGGLE SWITCH DPDT  

NCE

Momentary SPST-Red, Green, Black - 8pk

TCS

20 foot lengths of 32 gauge wire.

TCS

20 foot lengths of 30 gauge wire.

NCE

Euro 2-5   2 Circuit

Euro StyleTerminal Block 5 pk

NCE Pro Cab

The Pro Cab throttle provides the most user-friendly access to all system features. Uncomplicated menus on the easy to read, the backlit LCD display will guide you through the most advanced operations with a minimum of fuss.

The Pro Cab-R throttle has the same specification as the Pro Cab except that a radio board and battery holder has been added for operation as a radio throttle while retaining the plug capability of the Pro Cab.

FUNCTION CONTROL FOR THE LOCOMOTIVE LIGHTS F9 to F12

NUMBER KEYS

The keys 0 through 9.

When operating a loco if a number key is pressed it toggles the corresponding function on the loco. Use to access FUNCTIONS 1 to 9.

To access the function F9 you simply press 9

 SHIFT BUTTON

When pressed and held while pressing another key on the cab the alternate value of that key can be used.

To access the function F10 you simply press SHIFT and PROG/ESC at the same time to activate FUNCTION 10.

To access the function F11 you simply press SHIFT and EXPN at the same time to activate FUNCTION 11.

To access the function F12 you simply press SHIFT and 28/128 at the same time to activate FUNCTION 12.

Repeat the procedure to turn the function off.

How to operate the DCC Solutions 28 functions on your locomotive.

 EXTENDED FUNCTION CONTROL F10 to F28

 OPTION BUTTON

The OPTIONS button marked * (see picture) can be reprogrammed for use to access FUNCTIONS 10 to 28. Follow these simple steps.

1. Turn on your system and unplug the cable from your cab (Throttle)

2. Press and hold down the SELECT LOCO while plugging the cable back into your cab. The cab will now enter the initial setup program. At any time you may press PROG/ESC to exit.

3. Press enter FOUR (4) or possible FIVE (5) times depending on your cabs firmware until your screen reads PROG OPTION KEY...KEY VALUE = 94.

4. Enter a new value of 122 and press ENTER

5. Press PROG/ESC to exit.

Once reprogrammed pressing OPTION once will display F10 – F19 and pressing it twice will display F20 – F28. Pressing a number key will toggle that number plus 10. Example: Press OPTION once then 5 will activate F15. Repeat the same procedure to turn F15 off.

NCE Cab06 and Cab06R

The Cab06e uses an encoder knob for speed control. The Cab06 can be set to YARD mode. Yard mode makes the speed knob act as a "centre off" speed control. Turn the knob to the right and the loco will increase speed in the forward direction. Turn it to the left and speed will decrease until it gets to zero then it will start to increase speed in the reverse direction the farther you turn it to the left. Selection and control of individual or entire routes through turnouts (via the MACRO key), and our unique OPTION button that can be programmed to act as any button you wish, even those found on a much larger cab.

• Additional features include a 4-digit LED display, 29 functions, accessories with 6 recalls, including PowerCab

• The Cab06eR has the same specification as the Cab06, except that a radio board and battery holder have been added for operation as a radio throttle while retaining the plug capability of the CAB06. 

• For those who do not wish to use an encoder, NCE offer the CAB06P and CAB06PR. All the great features of the CAB06e but with a potentiometer.

• The MRRC recommends the Cab06P for radio operation as it offers a physical stop to mark stop.

NCE

RJ12-7' Cable for connecting UTP/DIN panel