DCC CONTROL

ESU Harness

6-Pin NEM651. Each harness comes with NMRA standard colour wire, length 300mm

Harness 18-pin Next-18 socket to open wires,88mm

ESU Boards

Makes installation easier and safer. First, all wires are connected to the soldering points of the adapter board. All contact points (terminals) are present on both - top and bottom and you can remove and reinsert your decoder at any time.

ESU Lokpilot Micro

#54650 , N scale, easy drop in Board design, six output functions, 

#53661 Nano Standard DCC, 8pin

#59818 V5 Micro Next18, no wires

#59925 Nano DCC, E24 Interface.

ESU

Led Lighting power Pick ups - 8pk

Lais 

Multi-Scale Track Tester-OO, HO & N

Helps to locate faults at track joints & points, etc. Place across the track and the multi-coloured Led will display Orange for DCC or Red & Green for DC power.

STX GE Diesel

TSU-1100 :1A Max

TSU-2200 : 2A  Max

TSU-21 PNEM : 1A Max

TSU-PNP :2A Max

TSU-N18 :1A Max

Switch Mode Power Supplies to suit the NCE system or others require a matching voltage

P514 power supply,5 Amp internationally approved for use with SB5, DB5, and PB5

P314 power supply,3 Amp internationally approved 

Do NOT purchase these for use with the Powercab

MRRC DP30-TX01  1.8 Amp internationally approved power supply for use with NCE PowerCab

NCE PH-5 DCC System

The PH-5  is the most user-friendly DCC system on the market. The Pro-Cab walks you through every operation with clearly labelled buttons and well thought out menu prompts in plain English on its backlit LCD display. The most often performed operations usually are just a single keypress.  

The PH-5 starter set has everything you need to get DCC equipped trains up and running with it's own power supply. The Quick Start Guide included in our system reference manual will have you up and running in less than 20 minutes.

PH-5 Specifications:
* Cabs: 60 maximum
* Number of simultaneous trains: 250
* Number of consists: 127 
* Range of locomotive addresses: 0-9999
* Range of consist addresses: 1-127
* Range of accessory addresses: 1-2044
* Continuous Output Current: 5 Amps
* Short circuit handling: Auto shutdown [500ms]
* Output voltage: Factory set to 14V, adjustable 10V to 16.5V

* Power supply included 19V DC, 5Amps @ 90VA 

PH-5 Radio Set adds:

* RB02 Radio Base Station including Antenna
* 6' RJ12 Cable for RB02
* Radio supplement manual

Lais

DC/DC Voltage Regulator

BRAWA

10 Metre Ring PVC Electrial Wire

Yellow, Red, Blue & Brown

NCE FMKM 

Fascia Mounting Kit for DCC Meter/Analyzer

DCC Meter not included.

NCE spares

Replacement 2 & 4 pin plugs for the NCE Systems.

NCE - RB-03

Second generation two way wireless for DCC. Will handle up to 48 wireless cabs. All features of your cabs are available without plugging in. Radio equipped cabs automatically switch from radio mode to tethered mode when plugged in. A seven-foot hookup cable is included.

NCE

Increase the saturation of the radio signal in hard to reach areas. Up to 30 Repeaters can be used. A forty foot hook up cable is included. Requires the use of one RB02 Radio Base Station.

NCE DB5 Dumb Booster

* The DB5 Dumb Booster expands the Smart Booster
* Can be used with an NCE Pro but the PB5 is better suited to that system and is recommended by the MRRC.

DB5 specification:

* Peak Output Current: 5.0 Amps - 3.5 Amps continuous
* Power supply: DC supplied with AU plug
* Short circuit handling: Auto-shutdown [500mS] 
* Output voltage: Factory set 

The DB5 can only be left on a short or overload for a maximum of 2 - 3 minutes. To ensure that the system is protected for a longer period all Australian supplied systems will have an EB1 circuit breaker supplied set to 2.5 amps.

The maximum amps permitted is 3.5 per EB1.

NCE

A true 4 Amp (12 Amp peak) self contained decoder for S, O and large scale with connectorized wire harnesses. Functions supported: Headlight(s) plus seven additional function outputs. All function outputs have extended effects generators capable of producing Mars lights, Ditch lights, Strobes, Beacons, etc. for each function output if desired. Size: 2.35" x 1.2" x 0.35".

NCE - Decoder

Designed as a replacement for "Bachmann DCC Equipped" diesels. Providing smoother, quieter operation.The decoder has 4 function outputs, complete with 2 Golden Glow LEDs.

NCE

Made to fit the Atlas N scale VO1000 loco with two functions

1.0 Amp (1.25 Amp peak) rating, two function outputs

2 function with 15 lighting effects

Full LED support

Nce Throttle replacement Matt

For Procab & Powercab

Lais

21Pin Decoder Blanking Plate.

TCS-1/6 Watt Axial Lead Resistor - 20pk

1.2K (1200) Ohm

TCS

INT-WH Intermountain Harness

LAIS #860044

6pin Decoder Blanking Plug for Model Railway Trains for NEM651  DCC Ready Locomotive.

Lais #860027

DCC LED Resistor Board. intended for use with DCC Mobile, Sound and Lighting drcoders.

NCE FMKP

Fascia Mounting Kit for DCC Partner

DCC Partner not included.

MARKLIN

Distribution Strip - 11 plugs - #72090

Consignment, As New 

Singlet Decoder with servo

Includes PC board with control, programming buttons, A 12" servo extension, a miniature servo, mounting screw and instructions.  For the price of a well-known slow switch machine, you also get a DCC accessory decoder and LED and control buttons. (Servo may be a different colour than shown.)

Note: The current demand from the decoders are rated at 0.1 amp demand each. On a DCC layout, the addition of an additional booster for a large number will require the additional booster. The NCE DB5 will provide 5 amps of power.

Micro Singlet Servo Decoder

The singlet has a baby brother, the Micro Singlet. It is a simple servo decoder designed to drive turnouts and only turnouts. It solves the problem of servo buzzing by turning the servo off at the end of the throw. Special circuitry and programming has been built in to accomplish this without a large jerk at restart.

Micro Singlet - designed exclusively to control turnouts with DCC or a pushbutton. Simpler than the classic Singlet it is designed only for turnouts.

Designed exclusively for switching turnouts with a servo

Miniature Servo Motor (SG90)

Sub-miniature 9g servo.  These have plenty of power for hinged point turnouts and smaller rail (code 55 and smaller) solid point turnouts - when used with the servo mounting kit (SMK002 below) then it can handle higher loads, up to code 100 non-hinged rail.  If the point rails are hinged then the rail size is not an issue - it has been used up to G scale. Our servo brackets (see below) are custom made to fit these servos. Size 1.25" wide (including mounting tabs) x 0.5" deep x 1.125" tall.  Servo lead about 7".  The label on the servo and the lead colors may vary between batches.  Works with all of our boards.

Note: The current demand from the decoders are 0.1 amps. On a DCC layout the addition of a additional booster for a large number will require the additional booster.

In-Line Servo Reverser

Reverse your servo throw direction by turning it around or reversing the servo linkage. Sometimes there just isn't room under a turnout to do this.  You can't reverse the servo direction by swapping wires since servos work by varying the pulse width and reversing the wires will just disconnect the servo.  In cases where you want to reverse the servo rotation direction, this servo reverser comes in handy.  If you put this in line with the servo it will swap the two ends about the center.  [It works by mirroring the pulse around 1.5 ms which is the center on a servo.  I.e. if a 2 ms pulse is input, the reverser will output 1 ms and if a 1 ms pulse is input it will output a 2ms pulse.]

Tam Valley

12" (30cm) Servo Extension Cable

3-wire servo extension cable 12" (30cm) long, 24 AWG stranded wire.  Added to the 12" cord that comes with most standard size servos you can power a switch up to 2 feet from an Octopus or Quad Servo board.

40" (100cm) Servo Extension Cable

24 AWG 3-wire servo extension cable.

12" Y-cord

Y cables are used to attach two servos to one output.  Both servos will move in the same manner at the same time.  Could be used, for example, to control a crossover or a passing siding.  Does not affect the servo power.  The Y can can also be used with the fascia controllers for the Quad-Pic to provide two control points for one switch.  Use one for a pair of servos and one for a controller at the same time and you can set up a passing siding with control points at both ends!

Tam Valley

Fascia Controller Mount

1/8" thick laser-cut acrylic, can be used to neatly mount your fascia controllers. Four screws hold it securely in place. Kit includes the 2 pieces and 4 screws. The pieces can be easily glued together with solvent designed for acrylics as MEK, other styrene glues will NOT work. Just put the pieces together and flow a small amount of solvent on with a brush.

Size 1.5" x 1.5" x 1/4" deep (without parts mounted)

TCS

10-foot lengths of the 32 gauge wire .022" diameter.

TCS

10-foot lengths of 30 gauge wire.

SPECIAL ORDER ONLY

NCE CS-02 Command Station

The CS 02 is the NCE Power Pro Command Station and is the most user friendly DCC system on the market. Plug in EPROMs allow you to update the system and no need to return the unit to the factory.

This is and ideal path for those wishing to move from another DCC system and seeking the NCE advantage. When migrating please contact us as most boosters are compatible with the NCE CS 02 Command station.

CS 02 Specifications:
* Cabs: 60 maximum
* Number of simultaneous trains: 250
* Number of consists: 127 
* Range of locomotive addresses: 0-9999
* Range of consist addresses: 1-127
* Range of accessory addresses: 1-2044
* RS232 computer interface included

NCE

The Auxiliary Input Unit provides connection of block occupancy detectors, switch position relays, etc. for purposes of signaling and/or computer control of your layout.

Simply plugs in to the Cab Bus.

Note: To be used with the NCE PowerCab the adress must be set at four [4]

NCE

Provides short circuit protection for one power district. Can be used with most DCC systems.

This is recommended for use with the Power Cab as a primary means of protection with the EB1 set to 1.5 amps for a distributed protection add a CP6.

DC Power Source

Single Pack

Ngineering

HO - 6"Aluminium Escutcheon - 8pk

Ngineering

HO - 18"Aluminium Lampshade

These aluminum lampshades and escutcheons have a very thin (.005") cross-section for prototypical appearance. The concave shape easily accepts many lighting products. Mounting holes are easily added.

Ngineering

O scale - 12"Aluminium Lampshade - 8pk

HO scale - 24"

2 each

MicroSuper-white LED .030 x .060" 

Extremely small size of just .030 x .060 and very bright, pure white light output. Device Voltage: 3.3V DC, Current: 20 ma, Average Life: 50-80,000 hours.

Ngineering

100uf Tantalum Capacitor - 6pk 

These tiny 16V DC capacitors can be "ganged" in parallel. Perfect for rolling stock lighting flicker control.

Ngineering

1/8-Watt SMD Resistor - 20pk

1500-Ohm

These precision resistors fit in the smallest spaces due to their flat shape and miniature size. Solder pads on each end are pre-tinned

Ngineering

1/8-Watt SMD Resistor - 20pk

1000-Ohm

These precision resistors fit in the smallest spaces due to their flat shape and miniature size. Solder pads on each end are pre-tinned

Ngineering

18"- Aluminum Lampshades - 8pk"

O scale 18", 1:32 scale 12"