DCC CONTROL

ESU Loksound V5

LokSound 5 has at least 10 amplified outputs. The decoders with PluX22 or 21MTC interface have four additional outputs for controlling servos or logic outputs.  All important lighting functions are supported. 

NCE

Euro 6-3 -  6 Circuit

Terminal Block 3 pk

AND-24 12-16AWG

Anderson Powerpole 24pk,

12 x RED, 12 x BLACK

AND-8 12-16AWG

Anderson Powerpole 8pk,

4 x RED, 4 x BLACK

NCE Quick Connect

Simply crimp to a NCE Feeder wire and push onto a NCE bus tap

No soldering required

Quick and easy

NCE DCC Meter

Volt/Amp Meter and Packet Analyzer

NCE spares

Replacement 2 & 4 pin plugs for the NCE Systems.

NCE - RB-02

Second generation two way wireless for DCC. Will handle up to 48 wireless cabs. All features of your cabs are available without plugging in. Radio equipped cabs automatically switch from radio mode to tethered mode when plugged in. A seven-foot hookup cable is included.

NCE

Increase the saturation of the radio signal in hard to reach areas. Up to 30 Repeaters can be used. A forty foot hook up cable is included. Requires the use of one RB02 Radio Base Station.

NCE DB5 Dumb Booster

* The DB5 Dumb Booster expands the Smart Booster
* Can be used with an NCE Pro but the PB5 is better suited to that system and is recommended by the MRRC.

DB5 specification:

* Peak Output Current: 5.0 Amps - 3.5 Amps continuous
* Power supply: DC supplied with AU plug
* Short circuit handling: Auto-shutdown [500mS] 
* Output voltage: Factory set 

The DB5 can only be left on a short or overload for a maximum of 2 - 3 minutes. To ensure that the system is protected for a longer period all Australian supplied systems will have an EB1 circuit breaker supplied set to 2.5 amps.

The maximum amps permitted is 3.5 per EB1.

NCE

Direct 8pin Plug Decoder

Fits Kato RS2/RSC2 and C44-9W,SD40-2, SD45, LifeLike FA1, Atlas GP40, AEM-7, GP7, U33C, U36C, C30-7, U23B locomotives and Australian HO Scale locomotives. 1.3 Amp continuous rating, 2 Amp peak. Six function outputs Size: 0.80" x 0.65" x 0.110".

NCE

Easy installation in many locomotives with Kato drive mechanisms such as Atlas/Stewart/Kato and Proto 1000. This decoder has five function outputs. Size: 2.85" x 0.65" x 0.125".

NCE - Large scale

A silent running decoder is specifically designed for high stall current large-scale locomotives. The decoder has 8 function outputs, each capable of ½ Amp and a stall rating of 30 Amps with 8 Amps average running current. It measures 3.7" x 1.4" x 0.6".

NCE

Control one twin coil switch machine. Has capacitive discharge for low current draw of track power. Provides connections for two "local control" pushbuttons. You can control switches from cabs and mini panels.

NCE

Kato UnitrackTM and LGB remote control turnouts can now be DCC controlled. The Switch-Kat provides connections for optional switch position indicator lights and "local control" pushbuttons. Simple installation, two wires to the track, two wires to the switch

NCE

Generic N scale sized decoder - 1.0 Amp (1.25 Amp peak) rating, four function outputs.

Size: 0.34" x 0.50" x 0.110".

NCE N Scale decoder

Plug and Play decoder for the N scale Atlas GP40-2, U25B, B23-7, 30-7, 36-7, GP38, SD25, Trainmaster, etc

1.3 Amp continuous, 2 Amp peak stall, all four function outputs have lighting effects generators.

Select from 15 different lighting effects

Full support LED lighting

NCE Plug and Play decoder for the N scale Atlas SD50, SD60M, SD60.

1 Amp (1.25 peak) rating.

Golden Glow LEDs are installed

Size: 3.475" x 0.370" x 0.120".

NCE

The Light-It is a multi-purpose programmable DCC lighting decoder. One Light-It contains three programmable lighting outputs with a complete array of lighting effects. Suitable for signal heads, passenger cars, locomotive lighting, cabooses, structure lighting, and many other uses.

Features:

• Works on DCC or DC (limited operation on DC)
• Works with loco, accessory or signal addressing
• Built-In Warm white LED (can be disabled)
• Up to 3 LEDs may be controlled separately
• Built-in resistors – just connect LEDs
• Functions as an NMRA Signal decoder with 18 aspects
• Each output is individually dimmable
• 15 Lighting EFX
• 18 Signal Aspects 
• Programed using your NCE PowerCab/ProCab handheld throttle
•  

NCE Drop in decoder for N-Scale Kato PA1, E8, Genesis P42, etc, White LEDs

1.0 Amp (1.25 Amp peak) rating, two function outputs

2 function with 15 lighting effects

Full LED support

NCE

Plug and Play decoder for the N scale Intermountain Tunnel Motor. 

1.0 Amp (1.25 Amp peak) rating, two function outputs

2 function with 15 lighting effects

Full LED support

NCE

8pin Four function decoder.

1 Amp rating, 1.25 Amp peak.

Measures 1.15" x 0.4" x 0.12".

Suits Austrains 47/49/NR late model

NCE - Decoder

Designed as a replacement for "Bachmann DCC Equipped" diesels. Providing smoother, quieter operation.The decoder has 4 function outputs, complete with 2 Golden Glow LEDs.

NCE

Decoder with a wire harness. Four function outputs.

1 Amp rating, 1.25 Amp peak.

Measures 1.15" x 0.4" x 0.12".

No plug

NCE

Decoder with NMRA 8pin plug.

Four function outputs, 15 lighting effects.

1 Amp rating, 1.25 Amp peak.

Measures 1.15" x 0.4" x 0.12".

NCE

Made to fit the Atlas N scale VO1000 loco with two functions

1.0 Amp (1.25 Amp peak) rating, two function outputs

2 function with 15 lighting effects

Full LED support

NCE Plug and Play decoder for the new Atlas "Classic" locomotives GP30, GP35, GP7, GP9

1.0 Amp (1.25 Amp peak) rating, two function outputs

2 function with 15 lighting effects

Full LED support

NCE Drop in decoder for Kato N-Scale F3 A&B

1.0 Amp (1.25 Amp peak) rating, two function outputs

2 function with 15 lighting effects

Full LED support

NCE

Control 8 Tortoise switch machines - Remembers the position of switch during power outages - Supports the full range of DCC accessory addresses (1-2044) - Easy address programming, no need to connect it to programming track - Connect optional "Button Board" for local push button control - Simple hook up, 2 wires to the track, 2 wires to each switch machine

NCE

Add up to 16 push buttons to Switch8-Mk2 - Must be used with momentary normally open (NO) Pushbuttons or toggle switches - Simple hook up, 3 wires to Switch8-Mk2

NCE

Control for 4 twin coil solenoid type switch machines (Atlas, Peco, etc) Supports the full range of DCC accessory addresses (1-2044) Runs from track power or external 9-15 Volt DC power supply Easy address programming, no need to connect it to programming track Inputs for local control panel push buttons Simple hook up, 2 wires to the track, 2 wires to each switch machine

NCE Switch-It

Controls two SwitchMasterTM, TortoiseTM or similar stall motor switch machines. Switch-It remembers the position of your switches during power outages. Each output of the decoder can have a completely different accessory address. The Switch-It provides connections for "local control" pushbuttons. Control switches from your cabs and your mini panels

NCE

3/4 Amp continuous, (1.2 Amp stall). Four function decoder with Harness and NMRA 8pin plug. Size: 0.85" x 0.63" x 0.1" - 22 x 16 x 2.4 mm

NCE

The Auxiliary Input Unit provides connection of block occupancy detectors, switch position relays, etc. for purposes of signaling and/or computer control of your layout.

Simply plugs in to the Cab Bus.

Note: To be used with the NCE PowerCab the adress must be set at four [4]

NCE

Detects DCC current being drawn in a block.

Connects to AIU-01 & Mini Panel for PC and automated control.

Works with most commercial signal systems.

Supports analogue output to 40 ma - requires a TX-01

NCE

Decoder Test Kit.

Works with any DCC decoder and tests motor forward and reverse, functions 0F, 0R, 1 & 2. Fitted with test plug's for NMRA 8 pin and JST 9 pin plugs. Supplied with 9 pin to 9 pin cable and  9 pin and cable which the user can add parrot beak cables to allow testing decoders like the DA-SR and any wire in decoders. Screw terminal to add motor for testing BEMF decoders.

NCE

Provides short circuit protection for one power district. Can be used with most DCC systems.

This is recommended for use with the Power Cab as a primary means of protection with the EB1 set to 1.5 amps for a distributed protection add a CP6.

NCE

CP6 Circuit Protector

Provides circuit protection for up to six sections of your railroad. Operates with any DCC system. Each globe allows 1 amp per section and sections can be connected together for more power per section.

NCE

Use one button to control multiple switches or macros on your NCE DCC system. You can have up to 30 pushbuttons, toggle switches, block detectors,etc. Can be connected for control of turnouts, signals and other devices. Easy programming, just plug in a Pro Cab. Simple hook up, one Cab Bus connection and 2 wires for each pushbutton or other input device. Can be used to perform simple automatic train control and other layout automation tasks.

NCE

USB to Serial cable

Connects PowerPro, Powerhouse & CS02 to USB 

Works with Windows-10 & Windows-7

NCE

Dual Relay connects to a Switch-it or Switch 8 decoder to provide two SPST or one DPDT relay output for switch up to 2 amps of power.

Typical uses:

Control polarity of dead frogs 
Automatic reverse loop control 
Turn staging yard tracks on on/off 
Provide isolated turnout position information to signaling ;
Computer control using AIU-01

Note: The markings for Positive [+] and negative [-] are reversed as is the markings for the normally open [n.o.] and normally closed [n.c.] .

This is a factory error in the printing and has no effect on the operation.

NCE 524-0242

Loco Wiring Kit for N/HO, 8 wire colors (80 feet ultra flex 30/32 AWG wire) , 3 sizes heatshrink

NCE 524-0243

Led Lighting Wiring Kit

NCE - Wire

30-32 Gauge Wire

Red - Right hand rail

Black - Left hand rail

Gray/Orange - Motor

Blue - Positive common

White - Front Headlight

Yellow - Rear Headlight

Genaral assignments but can vary

Green/Viloet - F1 / F2

Brown - Speaker

NCE-Layout Wiring Kit, 50 Foot DCC power bus.

NCE-Layout Wiring Kit, 100 Foot DCC power bus. 

NCE

Plug-in, 1.0 Amp (1.25 Amp peak) rated, four-function decoder with 6pin NEM 651 connector

4 function with 15 lighting effects, 

Full LED support

NCE-524-0243

LED lighting, 20 LEDs, LED Tester, 50 feet ultra flex #32 wire, 40 resistors, 3 sizes heatshrink

Nce Throttle replacement Matt

For Procab & Powercab

NCE - Spare parts

Thumbwheel / Encoder assembly for Pro Cab and Power Cab.

Note: Soldering is required.

TX-02

16VAC 5 amps AC power supply with fused primary supplied and spare fuses

This power supply is the Australian equivalent to the NCE P515 and is suitable to operate a NCE Pro 5 amp system.